Since PETG is slightly more stringy than PLA, you may want to reduce your print speed by about 20 mm/s to compensate. A print speed of 20 to 40 mm/s would significantly increase your chances of success. We suggest starting at 60 mm/s and gradually increasing the speed for prints that need more detail.įlexible materials must be printed at a much slower rate than rigid materials. You can increase this speed by using OctoPrint and alternative firmware like Klipper or Marlin. Most users print PLA at a speed of 45 to 65 mm/s on average. On the other hand, nobody wants to wait two weeks for a single print.ĪBS needs a print speed of about the same as PLA (45 to 65 mm/s is ideal). This is because a slower-moving hot end is far less likely to screw up finer info. Unfortunately, as your print speed increases, your print quality decreases.
It’s all about combining total time per job with print quality when it comes to finding your ideal print speed. If you’re going to use your Ender 3 to make ABS, you’ll probably need to create an enclosure to keep it cool and avoid warping and layer splitting.Ĭura Settings for Ender 3 (Pro/V2): Best Ender 3 Cura Profile Speed Print speed is a trade-off between time and detail (Source: Niall Mobsby via All3DP) The bed temperature for ABS should be about 110 ☌, which is slightly higher than that of PLA. The temperature in your bed should always be higher than the temperature in the room. PLA doesn’t need to be heated (but it helps), mainly if you use blue painter’s tape, hairspray, or glue for bed adhesion. The temperature of your bed is often influenced by the type of material you use.
RECAPĬura Settings for Ender 3 (Pro/V2): Best Ender 3 Cura Profile Bed Temperature No one’s happy with a warped 3D print (Source: Ultimaker) When calibrating your Ender 3, keep in mind that you can only change one setting at a time. It’s a good idea to print a temperature tower while trying out a new filament. In general, we think 200 degrees Celsius is a good average temperature for PLA. The ideal temperature varies by material (ABS: 220-250 ☌, PETG: 220-245 ☌), but the filament brand can also influence the temperature. Most PLA filaments need at least 180 degrees Celsius for smooth extrusion, but they may extend to 220 degrees Celsius until over-extrusion becomes an issue.
Over- or under-extrusion, curling, and blobs or zits may result from the wrong temperature setting. Temperature is one of the most critical settings. Hmm, maybe that was too much heat… (Source: Simplif圓D) Superb Ender 3 PLA ProfileĬura Settings for Ender 3 (Pro/V2): Best Ender 3 Cura Profile Hot End Temperature See also Ender 3 Vs Ender 3 Pro: The Ultimate Comparison Guideīefore we get into a more thorough overview of each environment, here’s a brief review of our recommended profile. You’ll have to adjust to different filaments and resolutions, of course.īefore we get into a more thorough overview of each environment, here’s a brief review of our recommended profile. We’ll create this profile for PLA by default, but we’ll also mention settings for ABS and PETG.
Go to “Add > Add a non-networked printer” in the preferences box.Īfter extending it, select Ender 3 or Ender 3 Pro from the “Crealit圓D” section.įrom here, you’ll be able to build your ideal profile using the default settings. Select “Settings > Printer > Handle Printers” from the drop-down screen. This is how you get to the stock profile: There is currently no profile for the V2, but most of the settings for the Pro should work for the V2. The Ender 3 Pro has its profile, so it’s a good place to start depending on which computer you’re using.
Creality, on the other hand, would certainly put most other 3D printers (or themselves) out of business if it was automated.įirst, the Ender 3’s stock profile on Cura is surprisingly fine.
Naturally, a printer at this price point would necessitate some bed leveling, manual calibration, and possibly a few tweaks. We’ve been blown away by these low-cost workhorses, which rival some of the higher-priced printers in terms of speed, efficiency, and print volume. To have great 3D prints, keep reading our best Cura settings for Ender 3.Ĭreality’s Ender 3, Ender 3 Pro, and Ender 3 V2 are probably the most successful 3D printer family of all time, providing an inexpensive entry point into the world of 3D printing. Cura and the Ender 3 (Pro/V2) are a 3D printing match made in heaven.